Lindberg products courtesy of Pacific Combustion

LINDBERG/BLUE M

Call or email us for assistance

FURNACES

TUBE FURNACES

1200°C SPLIT-HINGE TUBE FURNACES

Three Zone Controllers

CC58434C Three Zone Controller 1200°C Three Zone 16 Segment One Programmable Controller - Option One
Control console is fully wired and includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone. Includes three microprocessor-based PID controls (proportional, integral, derivative), single segment, single set point, 1 ramp to set point. Built-in adjustable high limit over temperature protection. Simultaneous LED display of actual temperature vs. set point. May be configured to display temperature in either °C or °F.

Option B Over Temperature Control (OTC)
Adjustable digital over temperature control, factory installed on selected control consoles with "B" designation; see chart. Protects furnace and load in the event of primary control circuit failure. Overrides main controller, assumes temperature control and shuts off power to furnace if high limit is reached. Manual re-set required for safety. Operates via magnetic contacts through signal from independent thermocouple. Available system on all three zone controller varieties. RS-485 communications port available as an option.

Optional RS485 Digital Communications Port
RS485 Digital communications port available as an option. Allows controller to be connected to a PC for remote monitoring and control of the furnace. Up to 30 units can be connected to one PC.

Model	Digital	With Programmer	With Overtemp Control	Volts, Hz	Amps	Exterior Dimensions H x F-B x W in"	Ship Weight lbs
CC58434C				208/240V, 50/60 Hz	20/30/20	17" x 19" x 14"	60
CC58434BC				208/240V, 50/60 Hz	20/30/20	17" x 19" x 14"	60

1200°C Three Zone 16 Segment One Programmable Controller - Option Two
Control console is fully wired and includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone.

Center Zone
One microprocessor-based PID programmable control (proportional, integral, derivative), with 1 program of16 segments for ramps (up and down) and 8 dwells (timed holds). Built-in adjustable high limit over temperature protection. Simultaneous LED display of actual temperature vs. set point.

End Zones
Two microprocessor-based PID control (proportional, integral, derivative), single segment, single set point which mimic the programmed profile of the center zone controller, but allow an offset up to 100°C. Offset is digitally displayed. RS-485 communications port available as an option.

Model	Digital	With Programmer	With Overtemp Control	Volts, Hz	Amps	Exterior Dimen. H x F-B x W in"	Ship Weight lbs
CC58434PC				208/240V, 50/60 Hz	20/30/20	17" x 19" x 14"	60
CC58434PBC				208/240V, 50/60 Hz	20/30/20	17" x 19" x 14"	65

1200°C Three Zone 16 Segment Three Programmable Controllers - Option Three
Control console is fully wired and includes advanced microprocessor-based digital control, a solid-state power module, on/off circuit breaker and thermocouple input jacks for each zone. Includes three microprocessor-based PID programmable controllers (proportional, integral, derivative), with 1 program of 16 segments for ramps (up and down) and 8 dwells (timed holds) to control each zone separately. Built-in adjustable high limit over temperature protection. Simultaneous LED display of actual temperature vs. set point. May be configured to display temperature in either °C or °F.

Model	Digital	With Programmer	With Overtemp Control	Volts, Hz	Amps	Exterior Dimen. H x F-B x W in"	Ship Weight lbs
CC584343PC				208/240V, 50/60 Hz	20/30/20	17" x 19" x 14"	60
CC584343PBC				208/240V, 50/60 Hz	20/30/20	17" x 19" x 14"	65

Back to 1200° Split -Hinge Tube Furnaces

Back to top

Call us today. We won’t make you wait for the future.